Trail Braking in Sim Racing Explained for Cleaner Corners
You brake hard and straight, release, turn in, and the car pushes wide while the faster driver behind you is already alongside. That gap is almost always trail braking.

You brake hard and straight, release, turn in, and the car pushes wide while the faster driver behind you is already alongside. That gap is almost always trail braking. Trail braking in sim racing means carrying a gradually reducing amount of brake pressure past the turn-in point, and it is the single technique that separates a tidy midfield lap from a competitive one.
I coach league drivers who are fast on straights and lose two or three tenths per corner on entry. This guide explains what trail braking actually does, how to practise it without spinning, and when you should not use it at all.
What trail braking actually does to the car
When you brake, weight shifts forward. The front tyres get pressed into the track and gain grip, while the rears get lighter. If you release the brake completely before turning, that weight rushes back to the rear, the front tyres lose some of their bite, and the car understeers just when you need it to rotate.
Trail braking keeps some of that weight on the front as you start turning. The front tyres have more grip for steering, the rear is slightly lighter so the car rotates more willingly, and you reach the apex with the car already pointing toward the exit. The result is a later braking point, a higher minimum speed in many corners, and an earlier throttle application.
The key idea is the grip budget. A tyre can give you roughly a fixed amount of total grip. Under full braking you use nearly all of it for slowing down. As you add steering, you must take away brake in proportion. Trail braking is simply trading brake for steering smoothly instead of switching from one to the other.
How to practise trail braking in sim racing
Pick one car and one track and stay with them for a full week. A front engined GT3 car such as the Mercedes AMG or BMW M4 is forgiving, and a track with a few clear heavy braking zones, like Brands Hatch Indy or Spa, gives you obvious practice corners. Then follow these steps:
- Set a reference lap. Drive ten laps the way you normally do and note your best time and your minimum speed in two chosen corners.
- Brake at the same point, release more slowly. Keep your usual braking point. Instead of snapping off the brake before turn-in, bleed it off over about 0.5 to 1 second as you start to steer.
- Aim for zero brake at the apex in slow corners. In a hairpin, you might still have 10 to 20 percent brake as you turn in, falling to nothing near the apex. In fast corners, the trail is much shorter and lighter.
- Move the braking point later, 5 metres at a time. Only once the release feels natural should you push the braking point. Use the track's distance boards or a fixed visual marker.
- Check telemetry. Your brake trace should look like a sharp peak followed by a smooth downward ramp, not a cliff. If the downward ramp has steps or spikes, your foot is reacting rather than releasing steadily.
Expect to be slower for the first two or three sessions. That is normal. Most drivers I work with gain 0.3 to 0.8 seconds per lap at a mid length circuit within two weeks once the release becomes automatic.
Hardware and settings that make it easier
You can trail brake on any pedal set, but some setups make it much easier to control the release:
- Load cell or hydraulic brake. These measure pressure rather than travel, which matches how muscle memory works. Drivers usually find trail braking far more repeatable after the switch. My colleague's review of load cell brake pedals goes into whether the cost is worth it.
- Brake force setting. If you can lock the wheels with only light pressure, you have no room to modulate. Set the pedal so maximum braking needs firm pressure, around 60 to 80 percent of your comfortable maximum.
- ABS in GT cars. ABS helps, but it can also hide sloppy releases. Practise with your car's normal ABS setting, and do not rely on the system to save a late turn-in.
- Brake bias. Moving bias rearward by 1 to 2 percent helps rotation on entry, but it increases the risk of rear lockup. Change it only after the technique is solid.
The common advice that holds new drivers back
Many beginner guides say "brake in a straight line, then turn". I understand why: it is safe and it avoids spins. But I think new drivers should start learning trail braking almost immediately, for a clear reason. Straight line braking builds a habit of releasing the brake abruptly before turn-in, and that abrupt release is exactly what unsettles the car. Unlearning it after a year of racing is much harder than learning a gentle release early.
The safer path is not "never trail brake" but "trail brake lightly". A beginner can start with a very short, very gentle trail, perhaps 5 percent pressure for a fraction of a second past turn-in. That alone stabilises the front and teaches the right feel without risking a spin.
The other overstated advice is that trail braking always makes you faster. It does not. In very fast sweepers and in cars with a lot of aerodynamic grip, carrying brake into the corner can cost speed. There, a lift or a light brake tap before turn-in is often quicker.
Trail braking in wheel to wheel racing
Trail braking also changes how you race others. Because you are still slowing as you turn, your line on entry is tighter and more predictable, which helps the driver behind you. It also makes defending fairer, since you are not forced into a late, wide entry that compromises the exit.
When you are attacking, be careful. A late lunge with heavy trail braking into a tight corner is how drivers lock the inside front and slide into the car they were passing. If you have not fully committed to the move, brake slightly earlier than usual and trail less. The broader racecraft is covered in how to overtake cleanly without wrecking both races.
Frequently asked questions
Is trail braking faster in sim racing?
In most slow and medium speed corners, yes, because it lets you brake later and rotate the car more efficiently. In very fast corners or high downforce cars, a lighter approach is often quicker. Telemetry comparisons on your own laps are the best way to check each corner.
How do I stop spinning when I trail brake?
Spins usually come from too much brake while turning, or from a sudden release. Reduce brake pressure more smoothly as you add steering, and move your braking point back to where you can control it. Shifting brake bias forward by 1 to 2 percent also adds stability while you learn.
Do you need a load cell pedal to trail brake?
No. You can trail brake on a basic potentiometer pedal, it is just harder to repeat precisely. A stiffer spring or rubber block helps those pedals feel more pressure based. A load cell makes the technique easier, but it does not replace practice.
More in Racecraft
Racecraft
Multiclass Racing Etiquette When Classes Share a Track
My worst incident in three seasons of endurance sim racing lasted about half a second.
Racecraft
Slipstream in Sim Racing and When to Pull Out of the Tow
You sit in the tow for the whole of the Monza main straight, closing on the car ahead every metre, then pull out at the last...
Racecraft
Rejoining the Track Safely in Sim Racing After a Mistake
You run wide at a fast corner, drop two wheels in the gravel, and the car comes to rest pointing the wrong way.