Rwxqsgd5 logo Rwxqsgd5Faster laps, honest setups
Racing Gear

Bass Shakers for Sim Racing and How to Fit Them Cheaply

I spent two seasons locking the fronts into the first corner at Monza without knowing it until I watched the telemetry afterwards. The wheel told me nothing useful.

A tactile transducer bolted under a sim racing pedal plate next to a small amplifier and speaker wire

I spent two seasons locking the fronts into the first corner at Monza without knowing it until I watched the telemetry afterwards. The wheel told me nothing useful. Force feedback reports what the steering rack is doing, and a locked front wheel on a straight brake pedal does almost nothing to the rack. The information I needed was in my feet and my back, and my rig had no way to deliver it.

Then I bolted a 40 dollar transducer under the pedal plate on a borrowed rig and found the lock up on the second lap. Not because the effect was realistic, which it is not, but because a sudden buzz at the moment of lock is unmistakable and arrives roughly 80 milliseconds before the car starts to understeer. That is the honest case for tactile feedback on a budget rig, and it has very little to do with immersion.

What a bass shaker is and what it is not

A bass shaker, properly a tactile transducer, is a speaker with no cone. The voice coil drives a weight instead of air, so the energy goes into whatever you bolt it to. Feed it a 45 Hz tone and the metal it is attached to vibrates at 45 Hz. Nobody hears much; everyone touching that metal feels it.

Three things it does not do. It does not replace force feedback, because it carries no directional information at all. It does not make a weak wheel base feel strong. And it does not add any sensation of lateral load, which is the thing a motion rig gives you and the reason motion rigs cost what they cost.

What it does carry is event information. Wheel lock, wheel spin, kerbs, gear shifts, engine note, road surface changes, and in some titles the ABS pulse as a distinct rhythm rather than a vague rumble. On a rally stage the surface channel alone is worth the money, because gravel and tarmac feel different through the floor long before they look different on screen.

The parts list, with prices that have held

You need three things: the transducers, an amplifier, and software to generate the signal. Nothing else, and no part of it is exotic.

A Dayton Audio Puck sits around 40 dollars and handles 25 watts. The BST-1 runs closer to 55 and takes 50 watts. A two channel class D amplifier from Fosi or Nobsound costs 55 to 75 dollars and is more than adequate, since you will run these well below their limit. Speaker wire and a 3.5 mm to RCA cable add maybe 12 dollars. Two channels done properly comes to about 170 dollars all in.

For software, SimHub is the standard answer on Windows and its ShakeIt effects are the reason most people install it. It reads telemetry from the sim and generates tones per effect, so you build a profile from parts: one effect for wheel slip, one for the engine, one for kerbs. Budget an evening for the first profile and twenty minutes for every one after that.

Four channels is where this stops being cheap. A four channel amp, four units and the extra wiring roughly doubles the cost, and the gain over two channels placed well is smaller than the forum enthusiasm suggests. I ran four for a year and went back to two.

Everyone tells you to buy the big one, and they are wrong

The advice you will read is to skip the small puck and start with a 50 or 100 watt unit, on the basis that more power is more feel. I have tested both on the same rig in the same week and the ranking depends entirely on what the unit is bolted to.

A 25 watt puck screwed into a 40 by 40 aluminium profile transmits more usable detail than a 100 watt unit on an 18 mm MDF desk top, because the desk absorbs the energy and turns it into a dull boom that tells you nothing. The MDF also rattles everything standing on it. My monitor buzzed at a specific engine RPM for a month before I worked out why.

Rigidity beats wattage, and placement beats both. If your rig is a wheel stand and a normal desk, put the transducer on the pedal plate or the stand frame, never on the desk. If you race from an office chair with the pedals on the floor, bolt it to a piece of plywood under the pedals and keep the chair out of it entirely. Our guide to picking a wheel stand that does not flex is relevant here for a reason nobody mentions: a stand chosen for stability also happens to be the only surface on a desk rig worth mounting a transducer to.

The other overstated claim is latency. People worry about it and it is not a real problem. SimHub generates the tone from telemetry and the delay through a USB sound card and amplifier is a few milliseconds, which is far below what anyone notices through their skin.

Fitting it in an evening

Do this in order. Skipping the first step is how people end up with a rattling rig and no idea which effect is responsible.

  1. Find the rigid point. Press hard on the candidate surface with your thumb. If it gives at all, keep looking. Pedal plate, seat frame rail and aluminium profile are good. Desk top, seat cushion and plastic trim are not.
  2. Bolt, do not stick. Use the mounting holes and a machine screw with a washer. Double sided tape works for a week and then the adhesive warms up and the unit buzzes against the metal.
  3. Wire with the amp off. Keep polarity consistent across both channels. Set the amp gain to about a third and leave it there until the profile is built.
  4. Build one effect first. Wheel slip only, nothing else. Drive two laps and raise the gain until lock up is obvious without the whole rig humming.
  5. Add the engine effect last. It is the one that masks everything else, so it goes in at low level or not at all. I run mine at roughly 20 percent of where it started.
  6. Check the floor. If you live above someone, stand in the room below while a friend drives. Below 40 Hz travels through concrete surprisingly well, and a sheet of 50 mm foam under the rig fixes most of it.

The common mistake is the opposite order: install everything, turn all effects to maximum, race once, declare it amazing, then quietly stop using it because the rig is a blur and you cannot tell kerb from gearshift. A tactile profile is useful in proportion to how little it does.

Where it sits against other upgrades

If you have a belt driven base, worn pedals and no tactile feedback, the pedals come first and nothing else is close. Braking is where lap time lives and a rubber potentiometer pedal gives you no reference point at all. The reasoning in our piece on whether a load cell brake is worth the money holds even if you never buy another thing.

After that, I would put a 170 dollar tactile setup ahead of a 600 dollar wheel base upgrade for anyone still making mistakes they cannot identify. The base makes a car you already drive well feel better. The transducer tells you what you did wrong. Those are different purchases and only one of them makes you faster in the first month.

What I cannot tell you is how much of this survives on a console. Transducers work fine, the amp works fine, but the telemetry side depends on what your title exposes and how, and I have only done it properly on a PC. More gear comparisons sit in the racing gear section if you are deciding between two upgrades at once.

FAQ

Can I use an old subwoofer instead?

Not well. A subwoofer moves air, so you get noise in the room and very little through the chair. The transducer exists specifically to put the energy into the structure rather than the air.

How many transducers do I actually need?

Two placed well covers almost everything: one at the pedals for slip and lock, one at the seat frame for road and engine. Go to four only after you have run two for a month and can name what is missing.

Will the neighbours hear it?

They may feel it. Airborne noise is low but low frequency energy travels through floor slabs. Isolating the rig with foam or rubber feet makes a bigger difference than turning the gain down.

Does this help in rally more than circuit racing?

In my experience yes, because surface changes and loose gravel carry almost no information through force feedback. On a circuit the gain is narrower and concentrated on brake lock, kerbs and traction loss out of slow corners.

JS
Jussi Saarinen

Jussi grew up watching rallies in the Finnish forests and now tests budget racing wheels on a desk that has survived four clamps.

More posts by Jussi

More in Racing Gear

01doorganico 084goad 3hot8 4465456 after5internprogram ahandfulofblessings ahmadpc ahomcybersecurity allodialresources annodex antiquesandperiodcollectibles aotc asianworldkashmir beedlectrics bloggertemplatefree bluefeatheragency bodyweightsolution campaign08blog carfixadvisor catstreetcollective cbstvsports cnfanspurchasing committeeof500yearsofdignityandresistance covertopsdjs cs-kaiyuangame cuestacomunicaciontotal cxoutlet dancebetgame deskgearhub destinyvillastay detectmagazine di33 diamondsteelbuildings donmo dyanadropship emarsysfinance emimattl escapechan eskitarih evautoplay everythingweddings-orlando farmzone feedviewerapp foxstudiosscratch gamevui123 gleasongrade greetingsday hacklabasu haskell iw-kaiyun jagoanproperti jilidskripsi joltbusinessfinance juegodepokergratis juegospucca kaeru-festival latestmehndidesigns lestanzediottaviano litemagazines localcommunityhero lustrsazan mariashebets menswheels newwebstechs1 nikkit ootheday oxigenvpn plurfitness prefetial probudgetcarpetcleaning psychicmrsmartin pyaten qvantor rejoignezlogis rexzbot riselayouts ruchin sakaltime shibiaowang shop-bot skrtips spotlesshaven strcoding tetapatrium topselller uneplanteartificielle vipertechcr webtech1223411 wo-kygaming yamaha-mekar yeknava yoybuysheets zenunwa yamaha-mekar jilidskripsi ankertoto ankertoto ankertoto