Sim Racing Brake Bias Settings and How to Find Your Number
You brake at the same marker every lap, yet sometimes the fronts lock and the car sails straight on, and other times the rear steps out and you spin before the apex.

You brake at the same marker every lap, yet sometimes the fronts lock and the car sails straight on, and other times the rear steps out and you spin before the apex. If that sounds familiar, your sim racing brake bias is probably fighting your driving style. It is one of the cheapest settings to change and one of the most misunderstood.
This guide explains what brake bias does, sensible starting numbers for common car types, a simple test session to find your own number, and when to adjust it during a race.
What sim racing brake bias actually controls
Brake bias, sometimes called brake balance, sets how the braking force is split between the front and rear axles. A value of 56 percent means 56 percent of the force goes to the front brakes and 44 percent to the rear.
Most of the force goes to the front because of weight transfer. When you brake hard, the car pitches forward, loading the front tyres and unloading the rears. The front tyres can handle more braking force at that moment, so the bias leans forward to match.
- More forward bias makes the car stable under braking but prone to front lock ups and understeer on corner entry.
- More rearward bias helps the car rotate on entry but makes rear lock ups and entry spins more likely.
The goal is not one perfect number. It is a number where both axles reach their grip limit at roughly the same time in the braking zones that matter most on that track.
Starting values by car type
Every game and every car presents brake bias a little differently, and some cars show an offset rather than a raw percentage. Treat these as rough starting points, then test.
| Car type | Typical starting bias (front) | Notes |
|---|---|---|
| GT3 cars with ABS | 53 to 57 percent | ABS hides small errors, so you can run a little further rearward |
| GT4 and touring cars | 55 to 59 percent | Lower downforce, more stable with a forward setting |
| Open wheelers without ABS | 54 to 58 percent | Often adjusted lap by lap as fuel burns off |
| Prototypes and hypercars | 52 to 56 percent | High downforce changes the ideal number through the stop |
| Road cars and street cars | 60 to 68 percent | Built for safety, very forward from the factory |
If the default setup already gives you a number, start from that. The setup engineer for the game chose it for a reason, and you are fine tuning, not starting from zero.
A ten lap test to find your own number
Pick a track you know well with at least one heavy braking zone from high speed and one slower, twisty corner. Turn off any assists you do not use in races. Then follow this sequence.
- Laps 1 to 3: Drive on the default bias. Note which corners cause front lock ups and which cause the rear to feel loose.
- Laps 4 to 5: Move the bias 1 percent rearward. If the car rotates better on entry without snapping, keep going.
- Laps 6 to 7: Another 1 percent rearward. The moment the rear feels nervous on the brakes into the fast corner, you have gone too far.
- Laps 8 to 10: Return to the last setting that felt stable and drive three consistent laps to confirm.
Move in steps of 0.5 to 1 percent. Bigger jumps make it hard to tell what changed. If you have telemetry, compare brake pressure and wheel speed traces between laps; a wheel speed trace that drops sharply on one axle shows exactly where a lock up starts. Our guide to sim racing telemetry for beginners shows how to read those traces.
How bias interacts with trail braking
If you trail brake deep into corners, a slightly forward bias usually works better than the setting a straight line braker would choose. As you release the pedal and turn in, the rears are already lightly loaded, and too much rear bias at that stage is a classic cause of mid entry spins. The technique is covered in our piece on trail braking in sim racing.
Why moving bias rearward for rotation is often wrong
A popular tip in league chats is "if the car understeers, shift the bias back". It can work, but I think it is the wrong first fix for most drivers. Entry understeer is usually caused by braking too hard while turning, carrying too much speed to the apex, or releasing the pedal too abruptly. Moving the bias back masks the technique problem and makes the car less forgiving in the braking zones where you are already doing it right.
It also hurts you over a stint. As tyres wear and fuel burns off, the car's balance shifts. A rearward setting that felt sharp on lap 3 can become an entry spin on lap 25. Fix the driving first, then use bias for the last few tenths. And if your real problem is the rear stepping out on the way out of the corner, bias is not the cause at all; see why you keep spinning on corner exit instead.
Adjusting brake bias during a race
In cars that allow it, changing bias from the wheel is normal practice. Map it to two buttons, and use these rules of thumb:
- Heavy fuel at the start: slightly forward. The extra mass makes the car less stable on the brakes.
- As fuel burns off: move back 0.5 percent every 10 to 15 laps if the fronts start locking.
- Worn rear tyres: move forward to calm the rear on entry.
- Rain or a damp track: move forward 1 to 2 percent, since rear lock ups are harder to catch in low grip.
- A track with one huge stop: set bias for that corner, since it is where the most time and the most risk sit.
Do not change it in the braking zone itself. Make adjustments on the straights, one click at a time, and check the result in the next corner.
Frequently asked questions
What is a good brake bias for GT3 in sim racing?
Most GT3 cars feel good somewhere between 53 and 57 percent front, depending on the car and the game. Start from the default setup value and move half a percent at a time. Mid engined cars often like a little more rearward bias than front engined ones.
Does brake bias matter if the car has ABS?
Yes, though the effect is smaller. ABS prevents full lock ups, but the bias still changes how the car rotates on entry and how hard the ABS works on each axle. A badly set bias with ABS feels vague and costs braking distance rather than causing spins.
Should brake bias be higher on the front or the rear?
Almost always higher on the front, because weight shifts forward under braking and the front tyres can carry more force. Values below 50 percent are rare and usually unstable. The real question is how far above 50 percent your car and driving style want it.
More in Sim Racing
Sim Racing
Sim Racing Damper Settings and What Each Click Does
The damper page is where setup confidence goes to die.
Sim Racing
Sim Racing FOV Settings and the Numbers That Work
A team mate of mine spent two seasons braking roughly fifteen metres early into the Dunlop chicane and could not work out why.
Sim Racing
Sim Racing Tyre Pressures and the Numbers That Matter
You download a setup from a league mate who is half a second quicker, put in three laps, and the car is wonderful.